Woodstock Nail Gun W1776 User Manual

MODEL W1776

2" NAILER KIT

OWNER'S MANUAL

Phone: (360) 734-3482 • Online Technical Support: [email protected]

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

#9553TS Printed in China

Model W1776 2" Nailer Kit

SAFETY

For Your Own Safety Read Instruction Manual

Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous

conditions. This manual uses a series of symbols and signal words which are intended

to convey the level of importance of the safety messages. The progression of

symbols is described below. Remember that safety messages by themselves do not

eliminate danger and are not a substitute for proper accident prevention measures.

Indicates an imminently hazardous situation which, if

not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, MAY result in minor or moderate injury.

It may also be used to alert against unsafe practices.

This symbol is used to alert the user to useful

information about proper operation of the

equipment.

NOTICE

Safety Instructions for Pneumatic Tools

5. KEEP CHILDREN AND VISITORS

AWAY. All children and visitors

should be kept at a safe distance

from work area.

1. KEEP ALL SAFETY DEVICES IN

PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND

WRENCHES. Form habit of checking

to see that keys and adjusting

wrenches are removed from tool

before operation.

6. MAKE WORKSHOP CHILD PROOF by

locking your shop and shutting off

air valves.

7. DO NOT FORCE TOOL. It will do

the job better and safer at the rate

for which it was designed.

3. KEEP WORK AREA CLEAN. Cluttered

areas and benches invite accidents.

4. DO NOT USE IN DANGEROUS

ENVIRONMENT. Do not use

8. USE THE RIGHT TOOL. Do not

force tool or attachment to do a

job for which it was not designed.

pneumatic tools in damp or wet

locations, or where any flammable

or noxious fumes may exist. Keep

work area well lighted.

9. DO NOT USE UNDER THE

INFLUENCE OF DRUGS OR

ALCOHOL.

-1-

Model W1776 2" Nailer Kit

Safety Instructions for Pneumatic Tools

17. DISCONNECT TOOLS before

servicing, changing accessories, or

moving to another location.

10. USE PROPER AIR HOSE for the

tool. Make sure your air hose is in

good condition and is long enough

to reach your work without

stretching.

18. DO NOT OVERREACH. Keep proper

footing/balance at all times.

11. WEAR PROPER APPAREL. Do

not wear loose clothing, gloves,

neckties, rings, bracelets, or

other jewelry which may get

caught in moving parts. Non-slip

footwear is recommended. Wear a

protective hair covering to contain

long hair.

19. USE THE RECOMMENDED

ACCESSORIES. Consult owner’s

manual for recommended

accessories. The use of improper

accessories may cause risk of

injury.

20. CHECK FOR DAMAGED PARTS

BEFORE USING. Check for binding

and alignment of parts, broken

parts, part mounting, loose bolts,

and any other conditions that may

affect machine operation. Repair

or replace damaged parts.

12. ALWAYS USE SAFETY GLASSES.

Also use a face or dust mask

if cutting operation is dusty.

Everyday eyeglasses only have

impact resistant lenses, they are

NOT safety glasses.

21. NEVER LEAVE UNATTENDED TOOL

CONNECTED TO AIR. Disconnect

the air hose and do not leave tool

until it is relieved of any built up

pressure.

13. WEAR APPROVED HEARING

PROTECTION. Air escaping from

pneumatic tools can exceed safe

exposure limits and may cause

hearing damage with prolonged

exposure.

22. NEVER ALLOW UNTRAINED

USERS TO USE THIS TOOL WHILE

UNSUPERVISED.

14. SECURE WORK. Use clamps or a

vise to hold work when practical.

It is safer than using your hand

and frees both hands to operate

tool.

23. IF YOU ARE UNSURE OF THE

INTENDED OPERATION, STOP

USING TOOL. Seek formal training

or research books or magazines

that specialize in pneumatic tools.

15. MAINTAIN TOOLS WITH CARE.

Keep tools lubricated and clean

for best and safest performance.

Follow instructions for lubricating

and changing accessories.

24. BE AWARE OF HOSE LOCATION

WHEN USING PNEUMATIC TOOLS.

Hoses can easily become a tripping

hazard when laid across the floor

or spread out in a disorganized

fashion.

16. REDUCE THE RISK OF

UNINTENTIONAL FIRING. Do not

carry tool with hand on trigger

and always disconnect from air

when not in use.

-2-

Model W1776 2" Nailer Kit

Additional Safety for Nailers/Staplers

1. HAND INJURIES: Do not place your

hands near the nail point of entry.

A nail can deflect and tear through

the surface of the workpiece,

5. HOSE USAGE: Make sure your air

hose is designed for the tool in

use, is in good condition, and is

long enough to reach your work

without stretching. However, an

overly long air hose in the work

area may be a tripping hazard.

puncturing your hand or fingers.

2. COMBUSTIBLE GASES: Never

connect the nailer to pressurized

oxygen or other combustible

gases as a power source. Only use

filtered, lubricated, and regulated

compressed air.

6. OPERATING QUESTIONS: If you

are not sure about the intended

operation, stop using the nailer.

Seek formal training.

3. SAFE HANDLING: Never point

the nailer at others! Do not keep

the trigger pulled when loading

fasteners, carrying, or holding

tool. Carry the nailer only by the

handle, never by any other part.

Do not carry the nailer by the air

hose. Disconnect the nailer from

the air hose when going up and

down ladders.

7. MAINTENANCE: Always disconnect

air from the nailer when servicing

or installing nails. During

maintenance, a nailer connected to

air may fire accidentally, causing

serious personal injury.

8. COMPRESSED AIR RATING: Do not

connect the nailer to compressed

air that exceeds 120 PSI.

9. CHECK VALVE: Do not use a check

valve or any other fitting that

4. CLEANING: Never use gasoline or

other flammable liquids to clean

the nailer; vapors in the nailer will

ignite by a spark and cause it to

explode.

allows air to remain in the tool.

10. MODIFICATIONS: DO NOT modify

this tool or bypass safety nose

mechanisms.

Never point this nailer at yourself

or another person! Always pay

attention to the direction this nailer

is pointed. Use this tool with respect

and caution to lessen the possibility

of operator or bystander injury.

Ignoring this warning may result in

serious personal injury.

Nailer/stapler accidents routinely

happen while moving the gun to

another location, such as up ladders,

to another room, or even another

job site. Always disconnect the gun

immediately after use and never

transport the gun while connected to

the air—even if the air compressor is

disconnected from its power source!

-3-

Model W1776 2" Nailer Kit

INTRODUCTION

Woodstock Technical

Tool Data

Support

Nail Size............................. 18 Gauge

Nail Length.............................. ⁵⁄8"–2"

Magazine Capacity................. 100 Nails

Air Inlet................................¹⁄4" NPT

Weight................................. 3.4 lbs.

Operating Pressure ...............60–100 PSI

This Model W1776 2" Nailer Kit has been

specially designed to provide many years

of trouble-free service. Close attention

to detail, ruggedly built parts and a rigid

quality control program assure safe and

reliable operation.

Woodstock International, Inc. is commit-

ted to customer satisfaction. Our intent

with this manual is to include the basic

information for safety, setup, operation,

maintenance, and service of this product.

We stand behind our tools! In the

event that questions arise about

your tool, please contact Woodstock

International Technical Support at

(360) 734-3482 or send e-mail to:

[email protected]. Our knowl-

edgeable staff will help you troubleshoot

problems and process warranty claims.

Read the manual before operation.

Become familiar with this nailer, its

safety instructions, and its operation

before beginning any work. Serious

personal injury may result if safety

or operational information is not

understood or followed.

If you need the latest edition of this

manual, you can download it from

http://www.shopfox.biz.

If you have comments about this

manual, please contact us at:

No list of safety guidelines can be

complete. Every shop environment

is different. Always consider safety

first, as it applies to your individual

working conditions. Use this and

other tools with caution and respect.

Failure to do so could result in serious

personal injury, damage to equipment

or poor work results.

Woodstock International, Inc.

Attn: Technical Documentation

Manager

P.O. Box 2309

Bellingham, WA 98227

Email: [email protected]

-4-

Model W1776 2" Nailer Kit

Compressed Air System

The Model W1776 is designed to be

operated at 60-100 PSI using clean,

dry, regulated, compressed air. Do not

exceed the 120 PSI maximum operating

pressure for your model.

Before using your nailer, regulate the

air pressure to find the optimum setting

within the specified operating range.

Start by testing the nailer at a low

setting, then increase the air pressure as

needed for satisfactory results.

Exceeding the maximum permissible

operating pressure may damage the

nailer and cause it to malfunction.

To protect yourself from personal

injury, DONOTallowtheairpressure

to exceed the recommended

pressure for this nailer!

An in-line filter/lubricator/regulator unit

can be installed as depicted in Figure 1.

This filter/lubricator/regulator unit

will protect your tool from damaging

water build-up, allow you to adjust and

maintain regulated air pressure to your

tool, and save you the inconvenience of

having to manually lubricate your tool

every time you use it.

If you plan on installing a filter/

lubricator/regulator unit in your

compressed air system, always follow the

connection instructions that come with

the unit.

��

Figure 1. Typical filter/lubricator/regulator installation order.

-5-

Model W1776 2" Nailer Kit

SETUP

Unpacking

This nailer kit has been carefully packaged for safe transportation. If you notice the

tool has been damaged during shipping, please contact your authorized Shop Fox dealer

immediately.

Inventory

The following is a description of the main components shipped with the Model W1776.

Lay the components out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the tool

or examine the packaging materials carefully. Occasionally we pre-install certain

components for safer shipping.

Model W1776 Inventory

Qty

A. Safety Glasses ........................... 1

B. Nail Gun .................................. 1

C. Carrying Case............................ 1

D. Hex Wrench 3mm ....................... 1

E. Hex Wrench 4mm ....................... 1

F. Pneumatic Tool Oil ..................... 1

-6-

Safety Nose

Model W1776 2" Nailer Kit

— If the nailer fires when the trigger

is pulled, without the safety nose

mechanism being depressed, then

the nailer is not working properly.

Safety Nose Mechanism

A safety mechanism on the nose of

the nailer protects against accidental

firing. When the trigger is pressed, the

nailer will not fire until the safety nose

mechanism is depressed.

— If you find that the safety

nose mechanism is not working

properly, check the lubrication of

its sliding components.

Before you use your nailer for the first

time, check the safety nose mechanism

to ensure proper function.

To check the safety nose mechanism,

do these steps:

DO NOT attempt to modify or bypass

the safety nose mechanism to make

the nailer/stapler fire without

pushing the safety nose down.

1. DISCONNECT NAILER FROM THE AIR

SUPPLY!

2. Make sure the magazine is empty and

contains no nails.

3. Make sure the trigger and the safety

nose mechanism move up and down

without sticking.

4. Connect the nailer to the air supply.

5. Without pressing the trigger,

depress the safety nose mechanism

against a scrap piece of wood that is

clean and free of any knots, nails, or

other foreign objects.

Operating this nailer can propel

objectsintotheair,causingimmediate

eye damage. To protect yourself,

always wear ANSI approved safety

glasses or goggles when operating this

equipment.

— If the nailer does not fire, then

the safety nose mechanism is

working correctly.

— If the nailer does fire when you do

this, immediately disconnect the

nailer from the air supply and call

Technical Support.

Thesafetymechanismisamechanical

device that can fail. Never rely on this

mechanism as an excuse to point the

nailer at yourself or any bystanders.

Serious injury may occur.

-7-

Model W1776 2" Nailer Kit

OPERATIONS

When replacing nails in your Model

W1776, follow these guidelines:

Gauge:........................................18

Length: .................................. ⁵⁄8"–2"

Capacity:................................... 100

To load your nailer, do these steps:

Figure 3. Loading nails into magazine.

1. DISCONNECT NAILER FROM THE AIR

4. Slide the nails all the way down to

SUPPLY!

the nose of the nailer.

2. Press down on the locking catch lever

and slide the magazine pusher all the

way back (see Figure 2).

5. Push the magazine pusher all the way

forward until the catch lever locks it

in place.

Operating

If you have not read the safety

instructions in this manual, do not

operate the nailer.

Catch

Lever

Before you operate your nailer, place five

to six drops of the included oil into the

quick connect fitting where the nailer

connects to the air supply.

Figure 2. Releasing locking catch lever.

3. Insert a strip of nails, pointed-end

down, into the magazine, as shown in

Figure 3.

To operate your nailer, do these steps:

1. Connect the air supply to the quick

connect fitting.

2. To test for proper nail penetration,

hold the nailer perpendicular to the

surface of a piece of clean scrap

wood that is thick enough for the

length of nails you have loaded.

-8-

Model W1776 2" Nailer Kit

3. Depress the safety nose mechanism

Adjusting Depth

against your workpiece.

A depth adjustment knob is attached to

the nose for setting the nail depth.

4. Before pulling the trigger, make sure

your free hand and other body parts

are positioned out of the way of a

potential path of a nail in case of

deflection.

To adjust the nail depth, do these

steps:

1. DISCONNECT NAILER FROM THE AIR

SUPPLY!

Deflection is caused when grain

irregularities, knots or foreign objects

inside the wood cause the nail to

change its path, resulting in the

nail puncturing the surface of the

workpiece, as shown in Figure 4.

2. Rotate the adjustment knob (Figure

5) clockwise to increase nail depth,

and counterclockwise to decrease nail

depth.

Besides damaging your workpiece,

deflection can cause injury if your

free hand is securing the workpiece in

the location that the nail deflects.

Safety Nose

Adjustment

Knob

Figure 5. Depth adjustment control.

3. Connect the nailer to the air supply

and test the nail depth. Repeat

Steps 1–2 until the nail penetration

depth is satisfactory.

Figure 4. Example of nail deflection.

5. Pull the trigger.

— If the nail drove into the wood

far enough, continue with your

intended operations.

DO NOT place your hands near the

nail point of entry. A nail can deflect

and tear through the surface of the

workpiece, puncturing your hand or

fingers.

— If the nail either went too far or

not far enough, then go to the

Adjusting Depth subsection on this

page.

-9-

Model W1776 2" Nailer Kit

Nose Release Lever

Clearing Jammed Nails

A jammed nail must be cleared before

using the nailer again.

To clear a jammed nail from the dis-

charge area, do these steps:

1. DISCONNECT NAILER FROM THE AIR

Nose Cover

SUPPLY!

Figure 6. Nose opened to clear jam.

2. Unlatch and pull the magazine all the

5. Remove the jammed nail with a

tool that will fit in the slot on the

underside of the nose, such as needle

nose pliers.

way back.

3. Remove the nail stick from the

magazine.

6. Throw the damaged nail away and

insert a new nail stick that only

contains clean, undamaged nails. DO

NOT use dirty or damaged nails!

4. Open the nailer nose with the nose

release lever (see Figure 6).

7. Close the nose cover, and push the

magazine all the way forward until

the catch lever locks it in place.

-10-

Model W1776 2" Nailer Kit

6. Open the nose cover as if to clear a

Replacing Pistons/

O-Rings

Under heavy use, a piston or piston shaft

may wear out. Replacement is quick

and easy. Contact your authorized Shop

Fox dealer to obtain the Piston Repair

Kit (Part Number X1776087) or the

complete O-Ring Repair Kit (Part Number

X1776088).

jammed nail.

7. Watch the discharge area and push

the top of the piston with your

finger. You will see the piston shaft

slide down the discharge area.

8. Taking care not to scratch or dent

the nailer parts, use a wooden dowel

or similarly shaped tool to push the

piston shaft back inside the nailer

until you can grip the piston head and

remove it from the cylinder. Clean

inspect the parts for cracks, wear, or

burrs.

9. Place a new O-ring on the new piston

and apply a thin film of the nailer

lubricating oil on the O-ring.

10. Insert the new piston in the cylinder.

Make sure that the grooves on the

piston shaft line up with those on the

guide at the bottom of the cylinder.

The new piston should easily slide

into the cylinder. DO NOT force the

piston into the cylinder! If the piston

is not easily inserted, double-check

the alignment of the piston shaft with

the grooves on the guide.

Always disconnect nailer from

air whenever servicing! During

maintenance, a nailer connected

to air may fire accidentally, causing

serious personal injury!

To replace a piston, do these steps:

1. DISCONNECT NAILER FROM THE AIR

SUPPLY!

11. After the piston is inserted correctly,

close the magazine. Replace the rear

cap assembly and tighten the four

cap screws.

2. Remove all nails from the magazine

cartridge, and clean the exterior of

the nailer.

3. Remove the four cap screws on the

back of the nailer, near the exhaust

port.

12. For more assistance, or to install a

complete O-ring set, refer to the

appropriate breakdown diagram

in the back of this manual for

component locations.

4. Remove the cap.

5. The top of the piston should now be

visible inside the cylinder, which is

housed in the head of the nailer.

-11-

Model W1776 2" Nailer Kit

CLEANING & LUBRICATION

Cleaning

Use a good solvent to clean the nose

assembly of the nailer. Always be sure

that the nailer is dry before using it

again.

Lubricating

Standard pneumatic tool oil has been

included with your new Shop Fox nailer

to help maintain its useful life. Place two

to six drops of oil in the nailer air inlet

(as shown in Figure 7) before every use,

or after 2 hours of continuous use.

Do not allow dust, chips, sand, etc.

into the air connectors or into the body

of the nailer; this may result in leaks

and damage to the nailer and the air

couplings.

Wipe off any excess oil near the nailer

exhaust to avoid dust build-up. When the

oil that was included with the nailer has

been completely used, replace with a

quality pneumatic tool oil.

Another option to manual oiling would

be to install a lubricator in your air

compressor line. If your air compressor

line already has a lubricator, then regular

lubrication of your nailer will not be

necessary. Just make sure there is always

oil in the lubricator.

Never clean this tool with gasoline

or other flammable liquids. Vapors

in the tool may ignite, causing

the tool to explode. Ignoring

this warning may lead to serious

personal injury or even death!

Figure 7. Lubricating nailer via air inlet.

-12-

Model W1776 2" Nailer Kit

W1776 PARTS BREAKDOWN

��

�

��

�

��

�

��

�

��

-13-

Model W1776 2" Nailer Kit

W1776 PARTS LIST

DESCRIPTION

REF PART�#

DESCRIPTION

REF PART�#

XPAW04M HEX�WRENCH�4MM

XPAW03M HEX�WRENCH�3MM

X1776003 CARRYING�CASE

X1776004 AIR�INLET�PLUG�1/4"�NPT

X1776005 END�CAP

45 X1776045 COMPRESSION�SPRING

46 X1776046 O-RING�13.2�X�1.9

47 X1776047 TRIGGER�VALVE�SEAT

48 X1776048 O-RING�11.2�X�1.6

49 X1776049 SWITCH�SHAFT

50 X1776050 O-RING�1.9�X�1.1

51 X1776051 SCREW�SPRING

52 X1776052 VALVE�COVER

53 X1776053 O-RING�7�X�1.5

54 X1776054 SAFETY�BRACKET

55 X1776055 COMPRESSION�SPRING

56 X1776056 DEPTH�ADJUSTMENT�SCREW

57 X1776057 PIN�1.5�X�8

X1776006 O-RING�40�X�2.65

X1776007 RUBBER�GRIP

XPSB41M CAP�SCREW�M4-.7�X�14

X1776009 LOCK�NUT�M4-.7

10 X1776010 GUIDE�BLOCK

11 X1776011 FIXED�MAGAZINE

12 X1776012 LATCH�BRACKET

13 XPSB18M CAP�SCREW�M4-.7�X�8

14 X1776014 LATCH�LEVER

58 X1776058 SLIDING�BRACKET

59 X1776059 COMPRESSION�SPRING

60 XPRP55M ROLL�PIN�3�X�27

61 X1776061 BRACKET

15 XPRP42M ROLL�PIN�3�X�20

16 X1776016 COMPRESSION�SPRING

17 X1776017 MAGAZINE�BRACKET

18 XPSB56M CAP�SCREW�M3-.5�X�10

19 X1776019 PUSHER�SPRING

20 X1776020 PUSHER�SHAFT

21 X1776021 PUSHER

62 X1776062 GUN�BODY

63 X1776063 SEALING�WASHER

64 X1776064 BUMPER

65 X1776065 CYLINDER�

22 XPSS23M

SET�SCREW�M4-.7�X�10

66 X1776066 COLLAR

23 X1776023 MOVABLE�MAGAZINE

24 X1776024 CARBON�STRIP

25 XPSB57M CAP�SCREW�M3-.5�X�6

26 X1776026 GUIDE�BLOCK

27 XPSB16M CAP�SCREW�M4-.7�X�16

28 X1776028 GUIDE

67 X1776067 O-RING�48.7�X�2.65

68 X1776068 MAIN�PISTON

69 X1776069 O-RING�23.5�X�2

70 X1776070 SEALING�WASHER

71 X1776071 GASKET

72 X1776072 SWITCH�VALVE

73 X1776073 O-RING�33.6�X�2

74 X1776074 COMPRESSION�SPRING

75 X1776075 O-RING�17�X�2.65

76 X1776076 SEALING�WASHER

77 X1776077 CYLINDER�COVER

78 XPLW01M LOCK�WASHER�5MM

79 XPSB15M CAP�SCREW�M5-.8�X�20

80 X1776080 EXHAUST�PORT

81 X1776081 COMPRESSION�SPRING

82 X1776082 SPECIAL�BOLT

83 X1776083 COMPRESSION�SPRING

84 X1776084 STEEL�BALL

29 X1776029 GUIDE�COVER�BRACKET

30 XPRP61M ROLL�PIN�3�X�12

31 X1776031 GUIDE�COVER

32 XPSB110M CAP�SCREW�M4-.7�X�6

33 X1776033 HANDLE

34 X1776034 HANDLE�COVER

35 X1776035 SLIP�BLOCK

36 X1776036 COMPRESSION�SPRING

37 X1776037 LOCK�PIN

38 X1776038 PIN�C4�X�12

39 X1776039 TORSION�SPRING

40 XPSB38M CAP�SCREW�M5-.8�X�25

41 X1776041 SEAL�COVER

85 X1776085 SAFETY�GLASSES

86 XPLW01M LOCK�WASHER�5MM

87 X1776087 PISTON�REPAIR�KIT

88 X1776088 O-RING�REPAIR�KIT

42 XPRP64M ROLL�PIN�3�X�18

43 X1776043 SAFETY�SPACER

44 X1776044 TRIGGER

-14-

Model W1776 2" Nailer Kit

Troubleshooting

Symptom

Possible Cause

Possible Solution

1. O-rings must be replaced

& operation of safety nose

must be checked.

Air leaking at

1. O-rings in trigger valve

housing are damaged.

trigger valve area.

Air leaking between 1. Loose screws in housing.

1. Tighten screws.

2. Replace O-ring

3. Tighten air fitting & use

teflon tape.

housing and hose

2. Damaged O-ring.

3. Loose air fitting.

Air leaking between 1. Damaged seal.

housing and cap.

1. Replace damaged seals.

Tool skips nails

while discharging.

1. Excessive air pressure.

2. Air leaks.

3. Dirt in nose.

1. Reduce air pressure to tool.

2. Tighten screws and fittings.

3. Clean nose.

4. Dirt or damage prevents nails 4. Clean magazine and

from moving freely.

5. Inadequate air flow to tool.

inspect/repair damage.

5. Check fittings, hose,

compressor, and air

pressure.

6. Worn piston O-ring or lack of

lubrication.

6. Replace O-ring and

lubricate.

7. Damaged trigger valve O-rings. 7. Replace trigger valve O-

rings.

8. Worn bumper.

9. Cap seal leaking.

8. Replace bumper.

9. Replace cap seal.

Tool runs slowly or 1. Undersized air hose.

has a loss of power. 2. Nailer is not lubricated.

1. Use a larger hose.

2. Lubricate nailer.

3. Broken spring in cap assembly. 3. Replace spring.

4. Exhaust port in cap is blocked. 4. Clean or replace damaged

internal parts.

Fasteners

1. Nails are the wrong size.

1. Use correct nails.

2. Use undamaged, clean

nails.

frequently jam the 2. Nails are bent or dirty.

nailer.

3. Magazine or nose screws are

loose.

4. Driver or driver guide are

worn or damaged.

3. Tighten magazine.

4. Replace worn or damaged

parts.

5. Nails are wrong angle.

5. Use correct angle nails.

Nailer does not

fire.

1. Nailer is not lubricated.

1. Follow lubricating

instructions.

2. Nail is jammed in magazine or 2. Clear nailer magazine or

discharge area.

3. Piston shaft is damaged.

4. Air pressure too low.

discharge area.

3. Replace piston shaft.

4. Check/increase air

pressure.

Air blows out of

exhaust cap; nailer

will not fire.

1. O-ring slipped out of groove or 1. Reinstall/replace suspect

damaged inside nailer.

O-ring; turn down air

pressure.

-15-

��

Warranty Registration

Name___________________________________________________________________________________

Street __________________________________________________________________________________

City _________________________State___________________________Zip________________________

Phone #______________________Email __________________________Invoice #___________________

Model #_________Serial #______________Dealer Name__________________Purchase Date___________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us

develop better products and services. Of course, all information is strictly confidential.

1. How did you learn about us?

_____ Advertisement

____ Friend

____ Website

____ Local Store

____ Other:

_____ Mail Order Catalog

2. How long have you been a woodworker/metalworker?

_____ 0-2 Years

_____ 2-8 Years

____8-20 Years

_____ 20+ Years

3. How many of your machines or tools are Shop Fox?

_____ 0-2 _____ 3-5

____6-9

_____ 10+

____ No

4. Do you think your machine represents a good value?

_____ Yes

5. Would you recommend Shop Fox products to a friend? _____ Yes

6. What is your age group?

_____ 20-29

_____ 50-59

____ 30-39

____ 60-69

____ 40-49

____ 70+

7. What is your annual household income?

_____ $20,000-$29,000

_____ $50,000-$59,000

____ $30,000-$39,000

____ $60,000-$69,000

____ $40,000-$49,000

____ $70,000+

8. Which of the following magazines do you subscribe to?

____ Cabinet Maker

____ Family Handyman

____ Hand Loader

____ Popular Mechanics

____ Popular Science

____ Popular Woodworking

____ Practical Homeowner

____ Precision Shooter

____ Projects in Metal

____ RC Modeler

____ Today’s Homeowner

____ Wood

____ Wooden Boat

____ Woodshop News

____ Woodsmith

____ Handy

____ Home Shop Machinist

____ Journal of Light Cont.

____ Live Steam

____ Model Airplane News

____ Modeltec

____ Old House Journal

____ Woodwork

____ Woodworker West

____ Woodworker’s Journal

____ Other:

____ Riﬂe

____ Shop Notes

____ Shotgun News

9. Comments:__________________________________________________________________

_____________________________________________________________________________

___________________________________________________________________

FOLD ALONG DOTTED LINE

Place

Stamp

Here

WOODSTOCK INTERNATIONAL INC.

P.O. BOX 2309

BELLINGHAM, WA 98227-2309

FOLD ALONG DOTTED LINE

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

Weed Eater Trimmer 545186832 User Manual
Weider Home Gym WEBE15420 User Manual
West Bend Electric Steamer 86604CF User Manual
Whirlwind TV Cables W5 48 User Manual
Wolf Appliance Company Cooktop CT36E B User Manual
Woodstock Treadmill M1036 User Manual
Xilinx Network Card 01ADASM User Manual
Yamaha CD Player YHT 470 User Manual
Yamaha Laptop Laptop PC User Manual
Zanussi Dishwasher DA 4342 User Manual